Xantrex 300 Uživatelský manuál

Xantrex Inverter 300Owner’s Guide445-0139-01-01 Printed in ChinaWeb: www.xantrex.comEmail: [email protected]: 1-604-422-8595Phone: 1-8

53 Xantrex 300 Inverter FeaturesThis section describes the main features of the 300 Inverter.Figure 1 shows the inverter’s AC panel.Figure 1 AC Panel

6When the inverter is connected to a DC power source and the On/Standby switch is on, AC power is available at the outlet.➂ Power LightThe green PWR l

7AC OutletsDepending on your geographic location, your 300 Inverter will have one of the following AC outlets.Figure 2 European AC OutletFigure 3 Brit

84 Connecting the 300 InverterThis section explains how to connect the 300 Inverter.Choosing a LocationFor the best performance, choose a location th

9Connecting the 300 Inverter to DC PowerYou can connect the inverter to a 12 volt DC power source using:• The cigarette plug wire assembly (page 10)•

10Using the Cigarette Plug Wire AssemblyLoads under 150 wattsWhen you are going to power loads under 150 watts, use the cigarette plug wire assembly.T

115. Turn on the inverter’s On/Standby switch. The PWR light comes on, and AC power is available at the outlet.Note: You may need to turn the vehicle’

12To connect the inverter:1. Remove the nuts from the DC terminals on the inverter.2. Place the red ring connector on the red (positive +) DC terminal

135. Place the black ring connector on the black (negative –) DC terminal, and then screw the black nut on until it is snug. Do not over tighten.Note:

14Figure 6 Hardwiring the 300 Inverter to a 12 Volt BatteryTo hardwire the inverter to the battery:1. Cut the clips off the cable clip wire assembly.

About XantrexXantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to

15wires in this assembly are appropriate for loads over 150 watts. The wires in the cigarette plug wire assembly are too small: do not use them.)2. Us

166. Remove the nuts from the DC terminals of the inverter.7. Place the red ring connector on the red (positive +) DC terminal on the inverter, and th

17Disconnecting the Battery• Before you disconnect the battery, turn off the AC load, and then turn off the in-line switch.Replacing the In-Line Fuse•

185 Operating the 300 InverterThis section describes normal operation as well as several problems that could occur when you use the inverter. If you

19that occurs when the engine starts may trigger a low voltage shutdown.• AC Overload Shutdown If you connect an AC load rated higher than 300 watts o

20Interference With Electronic EquipmentMost AC products operate with the 300 Inverter as they would with household AC power with the following except

216 Battery Operating TimeThe battery operating time of the 300 Inverter depends on the charge level of the battery, battery capacity, and the amount

227 TroubleshootingThis section describes problems you may encounter, the symptoms of each problem, possible causes, and various remedies.The AC load

23SymptomThe AC load does not operate. The light comes on when the inverter is turned on or when the AC load is turned on or plugged in. The alarm m

24The AC load will not operate; no inverter lights are on.SymptomThe cigarette lighter works in the lighter socket, but the inverter does not. Symptom

25Measured inverter output voltage is too low.SymptomThe AC voltmeter reading is 5 to 15 volts too low.Battery operating time is less than expected.Sy

268 Warranty Information What Does This Warranty Cover? Xantrex manufactures its products from parts and components that are new or equivalent to new

27building replacement products. If Xantrex repairs or replaces a product, its warranty term is not extended. Xantrex owns all parts removed from repa

28You must obtain a Return Material Authorization (RMA) number from Xantrex before returning a product directly to Xantrex. Do not return a product to

29To return your 300 Inverter for out-of-warranty service, contact Xantrex customer service for a Return Material Authorization (RMA) number, and foll

309 SpecificationsSpecifications may change without notice.Electrical AC receptacles 1AC output voltage 230 volts AC RMS ± 5%AC output frequency 50

31Physical Regulatory Dimensions (L x W x H) 200mm x 103mm x 66mm(7.9 in. x 4.1 in. x 2.6 in.)Weight 0.79 Kg (1.74 lb.)CE Mark Low Voltage Directiv

32

Contents11. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. Important Safety Information . . . . . . . . . . . .

2

1 Introduction Thank you for purchasing the Xantrex 300 Inverter. The 300 Inverter is part of a family of advanced, high-performance power inverters

22 Important Safety Information If the 300 Inverter is connected or used incorrectly, hazardous conditions may be created. Read and save this safety

3Warning!Risk of fire or explosion.The 300 Inverter contains components that tend to produce arcs or sparks. To prevent fire or explosion, do not inst

4 Caution!Risk of damage to the 300 Inverter.Reverse battery polarity (negative connected to positive; positive connected to negative) will damage the